This automatic jaw change chuck is ideal for high mix low volume production and use with automated robot load.
Search Results for: jaws
Kitagawa’s VE-LN Series Vises offers an ultra-low body height providing increased machining capabilities. Jaw lift is minimized to ensure high machining accuracy.
Kitagawa’s NRC Rotary Chuck is an exclusive air-operated chuck with a pneumatic cylinder built in the chuck body. This chuck is easy to fit on even Back motor-type NC rotary table.
Maximize the performance of your workholding! The most expensive lathe will not perform at its best if the chuck is not giving full grip force.
The Kitagawa Multi-Plate work grippers allows simultaneous machining with up to six grippers on one plate.
FOR IMMEDIATE RELEASE Schaumburg, IL – February, 2014 – Kitagawa-NorthTech, Inc. adds five new high performance steady rests to fleet…
FOR IMMEDIATE RELEASE SCHAUMBURG, IL – MARCH 23, 2013 – KITAGAWA-NORTHTECH, INC. introduces new wireless grip force meter. Maximizing…
Consistently high in quality, the KSB Series Soft Jaws are manufactured in inches and stocked at Kitagawa-NorthTech’s facility in Schaumburg, Illinois.
The PUES06 locks the workpiece in place by pulling back and clamping the inner diameter. Suitable for finish machining with high accuracy performance.
Three-jaw power wing work grippers secure the workpiece by pulling back and locking into place. Suitable for rough machining, OP-10 or OP-20.
Case Study: Sun Hydraulics Corporation Objective: Increase Accuracy | Reduce Change Over | Increase Throughput Background: Sun Hydraulics Corporation was co-founded…
Case Study: Midwest Pressure Systems Objective: Setup Reduction | Scrap Reduction | Increase Throughput Background: Midwest…
FOR IMMEDIATE RELEASE KITAGAWA-NORTHTECH, INC. Expands Chuck Sizes Schaumburg, IL…. Kitagawa-NorthTech has recently expanded their offering of precision lathe…
FOR IMMEDIATE RELEASE Kitagawa-NorthTech helps extend chuck life, strengthen grip force and improve safety. Kitagawa-NorthTech, Inc. strengthened their supplemental…
Thank you for your question! Each jaw should move 2.75mm, or 5.5mm on diameter.
(We will here assume that the cylinder actuating the chuck has the same or more piston stroke as required for…
The HB Series Hard Jaws are one of Kitagawa’s original equipment offerings that is consistently high in quality.
Dual Lock Chucks combine the gripping range of a sliding jaw chuck with pullback for positive Z axis location.
Vertical power chucks feature sealed master jaws to protect against chip and coolant contamination. The NV series power chuck is a low maintenance and suitable for both vertical and horizontal lathes.
The HW Series is suitable for square bar and other unusually shaped workpieces.
Three-jaw pull style power chucks are ideal for finish machining applications where length control is required.
Low profile, lightweight design using a self-contained air cylinder that requires only piping for air.
Power wing chucks come in three-jaw and two-jaw styles. These chucks are ideal for casting or forging work.
Cost effective solutions for high speed chucking and universal machining where long stroke and no through hole is required.
The N Series is a three-jaw wedge style power chuck with a closed center.
This power chuck’s unique built-in counter balanced mechanism assures stabilized jaw force every time and provide maximum grippping force at high speeds.
Excellent choice for both small and large batch production. This chuck offers quick and smooth jaw replacement.
Two and three-jaw lever-style power chucks are ideal for applications requiring extra long jaw stroke.
These high speed, large bore power chucks deliver up to 20% more speed, gripping force and bore size when compared to conventional chucks.
These high precision super bore power chucks are ideal for bar chucking requiring large bore and small chuck diameter.
Ideal for high speed chucking, bar chucking and universal machining.
High quality four-jaw idependent manual chuck with straight recess are versatile for most applications.
Radial and pull-back features allow high gripping forces, component length control as well as high repeatability of 0.0004″.
Offering the latest in high speed technology, these innovative designs ensure less jaw lift and higher speeds – delivering high accuracy and repetitive chucking.
Operating on a 2+2+2 clamping system, these chucks offer the ability to hold thin wall parts with minimal distortion.
Perfect solution for customized top tooling to greatly improve productivity results: perpendicularity, concentricity, parallelism, circularity, total runout, flatness – our custom innovations will Redefine Productivity!
Chucks 101 Learn more about the ABC’s of chucks and workholding: Types of Chucks Spindle Data Sheet Grip Force Maintenance…
ipt needs to be enabled for polling to work.<br /><br /> <a href=’http://www.constantcontact.com/survey/index.jsp?pn=mepc&#038;cc=ViraWidPOL’>Online Surveys</a> by Constant Contact.<br /><br /> Press…
Services: Repair, Rebuild, Installation and Training Kitagawa - NorthTech offers the highest level of workholding solutions, global engineering collaboration and exceptional…